Reekie Experience
5183 26/03/2012 PIN 80 Dia x 407mm
5183 26/03/2012 PIN 80 Dia x 407mm
5178 23/03/2012 MV Brother Glory crane 1 Slewing Column at Desan Shipyard
Deck crane slewing pedestal flange 2645od x 2475id (85 wide) face and Crane column 2830od x 2590id (120 wide) face
5167 19/03/2012 Spoolbody Upper Bore, remachine welded up Ø17.829″ +0.02/-0.02 x approx 5.35″, 14.875″ below top face
5164 15/03/2012 BRASS SWIVEL JOINTS 87.70 MM O/DIA X 57.15 MM I/DIA
5158 13/03/2012 ENGINE END BELL 3′-1 “X 9-1/8” O/ALL
MATSPEC BS 1452 G17 CAST IRON
5158 13/03/2012 EXTRA WORK DUE TO BAD CASTING
5156 12/03/2012 TOP FLANGE 1150 MM X 1120 MM X 40 MM THICK TO DRILL 12 OFF 45 MM DIA HOLES
5156 12/03/2012 8 SIDED BOTTOM FLANGE 1150 MM X 1000 MM X 40 MM THICK TO DRILL 28 OFF 45 MM DIA HOLES
5156 12/03/2012 TOP FLANGE 1150 MM X 1000 MM X 40 MM THICK TO DRILL 8 OFF 45 MM DIA HOLES
5156 12/03/2012 8 SIDED BOTTOM FLANGE 1000 MM X 1000 MM X 40 MM THICK TO DRILL 20 OFF 45 MM DIA HOLES
5156 12/03/2012 TOP FLANGE 1270 MM X 1270 MM X 40 MM THICK TO DRILL 16 OFF 45 MM DIA HOLES
5156 12/03/2012 SIDE FLANGE 810 MM X 640 MM X 40 MM THICK TO DRILL 24 OFF 33 MM DIA HOLES
5156 12/03/2012 8 SIDED BOTTOM FLANGE 1270 MM X 1270 MM X 40 MM THICK TO DRILL 32 OFF 45 MM DIA HOLES
5156 12/03/2012 TOP FLANGE 1270 MM X 1270 MM X 40 MM THICK TO DRILL 8 OFF 45 MM DIA HOLES
5156 12/03/2012 SIDE FLANGE 840 MM X 640 MM X 40 MM THICK TO DRILL 32 OFF 33 MM DIA HOLES
5156 12/03/2012 8 SIDED BOTTOM FLANGE 1270 MM X 1270 MM X 40 MM THICK TO DRILL 32 OFF 45 MM DIA HOLES
5157 12/03/2012 Modification to Carousel at Leith Imperial Dock, Drilling new sets of holes for replacement of 16 off roller way plates
5155 09/03/2012 Remachining of gearbox connection flange;
site visit and collection, strip unit, machine gearbox flange, machine seal plate
5150 07/03/2012 Transocean Legend, offshore (via Perth) Australia, 3.1/16″ BX154 hub
5150 07/03/2012 hire of Reekie R10 during May 2012
5150 07/03/2012 Hire of Reekie R10 equipment from 1st April 2012 to 30th April 2012
5146 06/03/2012 1300 UPPER FRAME TO MACHINE TAPER THEN WELD TAPER ONLY DRAWING 603 1504
5143 05/03/2012 P.A. TUBE CENTRALISING PIN
5142 02/03/2012 LEASE OF FACTORY SPACE TO BUILD
5142 02/03/2012 TO MACHINE BOTH FACES FLAT AND SQUARE TO BORE,COUNTER BORE TO 24.1/2″ DIA X 10 MM DEEP TRUE TO BEST FIT OF BOLTS
5138 01/03/2012 additional costs to original PO value for work completed during the period Sat 10th to Mon 12th March
5138 01/03/2012 Alcan Lynemouth Power Station, Unit 1, IP turbine casing bottom half, top cover removed,
5136 28/02/2012 Saipem Total Elgin B jacket piles, four off
2591 od x 80 wt ends machined to clean up flat and perpendicular to c/l within 1mm to Ra3.2 micron finish
5128 23/02/2012 VOS Supplier, Rudder Stock Housing Machining
Case Studies
View All >
Tartan Platform – Releasing Caisson from Dead Weight Support
The customer required a robust solution to release one of their caissons from a unique dead weight support structure. The caisson had a cone feature that nested into a mating cone in the platform support.
Find Out More >
Machining of Hang off Module (HOM) Rails on Deep Blue Vessel
The rails that the HOC runs on had become extremely worn and were affecting operations. The pair of rails, 11,080 mm long x 230mm wide, needed to be machined flat and to a common plane within 0.25mm.
Find Out More >