Reekie Experience
4703 16/05/2011 1.3/4″ / 2″ BSF Stepped Stud
4703 16/05/2011 Main Steam Drain Line WP
4695 12/05/2011 MS SPARGE TUBEPLATE 913 MM O/DIA X 13 MM THK
4695 12/05/2011 MS SPARGETUBE GUIDE PLATES 902 MM O/DIA X 6 MM THK
4695 12/05/2011 MS BAFFLE PLATES 910 MM O/DIA X 13 MM THK
4696 12/05/2011 Insert / bush 275+0.056+0.186 id x 325+/- 0.04 od x 313 long with 12mm long R100 id and od at ONE end
4696 12/05/2011 Oyster 2, Cylinder Heel Casting Insert
4696 12/05/2011 Oyster 1-off stub shaft sleeve 1200mm od x 1160mm id x 600mm long super austenitic stainless steel sleeve
4696 12/05/2011 Oyster 2, bushes for latch pin bores, steel, 190 od x 160.3 – 0 + 0.3 id x 100 long
turn to suit insitu bored diameters
4690 09/05/2011 Vessel Grampian Defender, Oil stand by vessel, azimuth thruster unit housing. Boring 2 off Ø660×70 locating rings. Two crews required to complete work asap.
4686 05/05/2011 1000 CONEHEAD
REMACHINE AS PER DRAWING 603-9106
4686 05/05/2011 49 MM ECCENTRIC 1000 AUTOMAX
TO MEASURE ALL BEARING SIZES TURN IF REQUIRED AND FIT SLEEVE
4686 05/05/2011 ONE PIECE UPPER FRAME (MC) TO MACHINE TAPER,WELD AND REMACHINE TAPER
4687 05/05/2011 MS TUBE 24 ” SCHED 80 X 200 MM LONG
4687 05/05/2011 MS TUBE 24″ SCHED 80 X 1250 MM LONG
4687 05/05/2011 MS TUBE 16 ” SCHED 60 X 820 MM LONG
4687 05/05/2011 MS TUBE 8″ SCHED 80 X 690 MM LONG
4687 05/05/2011 MS TUBE 6″ SCHED 80 X 590 MM LONG
4687 05/05/2011 MS TUBE 4 ” SCED 40 X 460 MM LONG
4687 05/05/2011 M S TUBE 16″ SCHED STD X .500″ WALL X 820 MM LONG
4687 05/05/2011 MS TUBE 12″ SCHED STD X .375″ WALL X 820 MM LONG
4687 05/05/2011 MS TUBE 10″ SCHED STD X .365″ WALL X 770 MM LONG
4687 05/05/2011 MS TUBE 8″SCHED STD X .322″ WALLX 690 MM LONG
4681 04/05/2011 GENERAL PICKUP AND DELIVERY OF GOODS
4681 04/05/2011 SERVO CYLINDER TOP BUSH
4681 04/05/2011 MANUFACTURE OF NEW PISTON
4681 04/05/2011 BORING & HONING OF SERVO CASING
4684 04/05/2011 Attemperature Butt Weld CW1
4677 03/05/2011 BRUSH PLOUGH CARRIERS c/w MK1,2,3,12
4678 03/05/2011 C.S. BRUSH PLOUGHS c/w FLATS and SCREWS
Case Studies
View All >
Tartan Platform – Releasing Caisson from Dead Weight Support
The customer required a robust solution to release one of their caissons from a unique dead weight support structure. The caisson had a cone feature that nested into a mating cone in the platform support.
Find Out More >
Machining of Hang off Module (HOM) Rails on Deep Blue Vessel
The rails that the HOC runs on had become extremely worn and were affecting operations. The pair of rails, 11,080 mm long x 230mm wide, needed to be machined flat and to a common plane within 0.25mm.
Find Out More >