Reekie Experience
4680 03/05/2011 ISM Shaft Repair of Drum Finisher Shaft
4675 29/04/2011 1300 UPPER FRAME TO MACHINE TAPER THEN WELD TAPER ONLY DRAWING 603 1504
4672 27/04/2011 Brake Fluid Drain pipework
4672 27/04/2011 Float LH Horiz Stab
4672 27/04/2011 2IN HONING TOOL ASSEMBLY
4672 27/04/2011 Drill bush, 1/4″ OD, 1/8″ ID, 1.5D
4672 27/04/2011 Drill bush, 5/16″ OD, 5/32″ ID, 1.5D
4672 27/04/2011 Parting off tool 3/8 square as per sketch (created from 12×12 No.16 butt welded lathe tool
4672 27/04/2011 HEXAGON METRIC T-HANDLE BALL DRIVER SET 7 PCE (2.5,3,4,5,6,8,10)
4672 27/04/2011 ALUMINIUM DEMO RIG – INSERT
4672 27/04/2011 1.1/4″ A/F SPANNER
4670 26/04/2011 Bauce Machine, repair to Ø60 x 35 long shaft
4669 22/04/2011 MS TUBEPLATE 1090 MM O/DIA X 75 MM THK
4664 20/04/2011 Snubbers, 3 sets of 4 rollers ptfe cones
4665 20/04/2011 CUP (MK 16)
4658 18/04/2011 WEAR PLATE BOLT c/w NUTS
4652 15/04/2011 Oyster 2 Project -WEC, wave energy convertor, one pair of base frames, one left hand one right hand, main bearing seating faces, mill areas required to clean up flat to at least the required dimensions and to required dimensions/angles from datum surfaces
4655 15/04/2011 ARRANGEMENT OF 110 SERIES CEPAC SM D/A CYLINDER BUSHED REAR EYE MOUNTED
4656 15/04/2011 Longannet Unit 1 outage, No 1 and No 3 HP steam strainer chests
4650 14/04/2011 Drilling North and South Base Frame Arms M24 holes
4650 14/04/2011 Oyster 2, 0430, two outboard torque arms, drill & tap four M36 holes 75 dp on 440 pcd (three at 30 degrees, one at 45 degrees) note hand, counterbore one 150 dia
0440 two cylinder heel castings, per casting drill & tap two sets of seven holes M36 x 75
4650 14/04/2011 Oyster WEC Piles, two 3800 id x 3960 od (80 wt) piles , top end face, drill & tap 8 pairs of holes on 3880 pcd, 200 crs, 100 pitch from centre 50 dia radial holes, drill 21 dia x 40 dp, and tap M24 x 30 length full form thread
4650 14/04/2011 Modificationm to Ram Frame (requested by APL)
4650 14/04/2011 insitu bore out 4 lines (pairs) of 275 id bushes to obtain required clearance from mating pins
torque arms/stub shaft arms and cylinder heel castings
4650 14/04/2011 Machining overcast material on torque arms
4650 14/04/2011 Survey and then possible machining of bearing housing casting.
4650 14/04/2011 insitu line bore one member of each of two pairs of bores from 160 to clean up coaxial with other member through 100 thk, 400 gap, maybe to 190 dia
4650 14/04/2011 Oyster 2 Project -WEC, wave energy convertor, one pair of base frames, one left hand one right hand, main bearing seating faces, mill areas required to clean up flat to at least the required dimensions and to required dimensions/angles from datum surfaces
4650 14/04/2011 Oyster 2 Project – Laser Alignment Assistance
4650 14/04/2011 Oyster 2 Project – Laser Alignment Assistance
Case Studies
View All >
Tartan Platform – Releasing Caisson from Dead Weight Support
The customer required a robust solution to release one of their caissons from a unique dead weight support structure. The caisson had a cone feature that nested into a mating cone in the platform support.
Find Out More >
Machining of Hang off Module (HOM) Rails on Deep Blue Vessel
The rails that the HOC runs on had become extremely worn and were affecting operations. The pair of rails, 11,080 mm long x 230mm wide, needed to be machined flat and to a common plane within 0.25mm.
Find Out More >