Reekie Experience
4451 24/11/2010 MH32 Insitu Milling, Facing and Boring Machine
Airbus A318 Undercarriage
JK Anchorage Machining
4451 24/11/2010 M16 X 180 MM LONG HEX HEADED SET SCREW
GRADE : 8.8 (HIGH TENSILE)
4451 24/11/2010 Training on use of MH32 Machine at Birtish Airways
4452 24/11/2010 MS RUB RING 32.830 ” O/DIA X 28.540″ I/DIA X 2.224 ” O/ALL
4446 22/11/2010 1000 MAIN FRAME REPAIR WITH NEW 50D RING
4447 22/11/2010 Sims Malaysia, repair to spoolbody tree to Drg No x232763 01
4444 18/11/2010 MS SUPPORT BLOCKS 69 MM X 100 MM X 300 MM LONG
4444 18/11/2010 MS SUPPORT BLOCKS 60 MM X 100 MM X 300 MM LONG
4436 11/11/2010 Carsfad Power Station, Turbine Generator Thrust Bracket, Machine Ø49 x 80 deep location diameter
4433 10/11/2010 MV Ronja viking, a live fish carrier, Caterpillar engine feet/seating, core drill or bore and ream two aftermost holes to suit M27 fitted shoulder bolts, thro 30 thk steel, 58 thick chock fast, 32 thk steel after realignment and chock fast by Fine Align
4429 04/11/2010 DAVIT MASTS 65250 SERIES
4429 04/11/2010 DAVIT CAPSTAN NUT
4429 04/11/2010 PHOSPHER BRONZE WASHER DAVIT WASHER
4424 26/10/2010 four lengths of 21.1/2″ od x 0.559″ wt carbon steel 50D pipe face two ends of two lengths to 188.1/2″ and two to 227.1/5 bore 20.38″ plus or minus 0.01″ x 6.1/2″ length form 5 degree transition between bored and unbored diameters form 38 degree (from fac
4418 22/10/2010 EN 24 SHAFT 160 MM O/DIA X 1000 MM LONG
4418 22/10/2010 EN24T SHAFT 140 MM O/DIA X 910 MM LONG
4420 22/10/2010 TO MACHINE TAPER FOR CONEHEAD 1300 M/C WELD UP TAPER RESET AND MACHINE TAPER 39.2 ° TO 4 MM DIMENSION
4421 22/10/2010 SMIT Young, Bore Port Side Shaft “P” Bracket
4411 20/10/2010 ST ST INDICATOR COLUMN 1.00″ O/DIA X 5.120″ O/ALL
4411 20/10/2010 ST ST PISTON ROD 1.258″ O/DIA X 13.077 ” LONG
4411 20/10/2010 STEEL INDICATOR 2.500″ O/DIA X3.500″ O/ALL
4411 20/10/2010 ST ST LINER 2.3770″ O/DIA X 4.440″ LONG
4411 20/10/2010 MS SPACER 3.620″ O/DIA X 2.000″ I/DIA X0.090″ THK
4410 19/10/2010 MS TIE BAR CLIPS 140 MM X 70 MM X 10 MM
MAT SPEC :MILD STEEL
4407 14/10/2010 C.S. BRUSH PLOUGHS c/w FLATS and SCREWS
4405 13/10/2010 F5 INNER BARREL BRUSH SEAL CONVERSION
4399 08/10/2010 Aubin Canisters 1 & 2 609 id x 10 wt vessels 1390 and 1690 overall length with 550.4 id x 1045 od x 70 thk flanges with welded up v ring grooves, machine weld overlay in Reekie works
4401 08/10/2010 SUPPORT BEAM ASSEMBLY C/W WEAR PLATE 2430 MM LONG X 250 MM WIDE X 280 MM O/ALL
4394 06/10/2010 1000 MAIN FRAME REPAIR WITH NEW 50D RING
4396 06/10/2010 SUCTION END BELL
Case Studies
View All >
Tartan Platform – Releasing Caisson from Dead Weight Support
The customer required a robust solution to release one of their caissons from a unique dead weight support structure. The caisson had a cone feature that nested into a mating cone in the platform support.
Find Out More >
Machining of Hang off Module (HOM) Rails on Deep Blue Vessel
The rails that the HOC runs on had become extremely worn and were affecting operations. The pair of rails, 11,080 mm long x 230mm wide, needed to be machined flat and to a common plane within 0.25mm.
Find Out More >