Reekie Experience
3805 03/09/2009 WASHER 70 MM O/DIA X 26 MM I/DIA X 20 MM THK
3805 03/09/2009 BAR FOR SWIVEL HOIST RING 80 MM O/DIA X 132 MM O/ALL
3805 03/09/2009 WASHER 70 MM O/DIA X 26 MM I/DIA X 20 MM THK
3805 03/09/2009 BAR FOR SWIVEL HOIST RING 80 MM O/DIA X 132 MM O/ALL
3793 28/08/2009 PREPARE EQUIPMENT AS PER THE JOBPACK
3793 28/08/2009 DAILY HIRE OF DR50
3790 27/08/2009 hire of Reekie model R55 air
3784 21/08/2009 R28 TOOL HOLDER ASSEMBLY
3785 21/08/2009 R28 TOOL HOLDER ASSEMBLY
3776 17/08/2009 ISM at Alexandra Dock Bootle of Metso shredder, one or two hing pin bores on middle housing machine weld repairs to finish 380 dia H7 thro 280 length, reaching through 405 dia holes thro 130 outer plates, bores approx4m apart
3771 10/08/2009 standby boiler feed pump ISM of 73mm od face of 1.1/2″ BSP connection
3767 07/08/2009 ISM Platen 10 off Hole Positions Ø70×45.5 with Ø110x12dp counterbore
3756 31/07/2009 Buzzard PS Deck crane pedestal ISM top 3100 id x 3445 od face to clean up flat within 0.2mm survey and produce post machining DC flatness report
3749 28/07/2009 SHAFT 30 MM DIA X 180 MM LONG
3749 28/07/2009 SHAFT 30 MM DIA X 150 MM LONG
3746 22/07/2009 DAILY HIRE OF R90
3746 22/07/2009 PREPARATION OF EQUIPMENT FOR HIRE
3746 22/07/2009 RETURN OF EQUIPMENT
3746 22/07/2009 TRANSPORT OF EQUIPMENT TO SITE
3743 20/07/2009 RETAINING PIN
3743 20/07/2009 OUTER CLEVIS LUG FOR TUBES
3741 16/07/2009 Livingston 9000 ton upset press ISM lower slide assembly any NCR’d holes of two sets of ten 2″ UNC to be opened out and retapped
3741 16/07/2009 Livingston 9000 ton upset press ISM guide column slot, on column and on housing, 2.5″ wide x 1.17/64″ deep x 24″ long, to clean up parallel/perpendicular to 3.5/8″ dimn from holes
3741 16/07/2009 Livingston 9000 ton upset press tailrod ISM to open out one hole from 2″ UNC to 3″ UNC 4tpi and maybe a 2nd hole in other tailrod
3734 15/07/2009 ism Montrose North Pedestral Crane Test Piece 6″x2″ MH32
3735 15/07/2009 SUPPLEMENT FOR WMG-BOLLARD-061018-CO
3732 14/07/2009 F5 INNER BARREL BRUSH SEAL CONVERSION
3731 13/07/2009 BASEFRAME 3550 MM LONG X 900 MM WIDE
3727 09/07/2009 ISM crane pedestal 1265 id x 1448 od x 50 thk to clean up flat within 0.19mm
3729 09/07/2009 Irvine boiler blow pipe work pad at bottom of boiler ISM to remove 3 sheared seized studs and open out all 8 holes to slightly larger new thread
Case Studies
View All >
Tartan Platform – Releasing Caisson from Dead Weight Support
The customer required a robust solution to release one of their caissons from a unique dead weight support structure. The caisson had a cone feature that nested into a mating cone in the platform support.
Find Out More >
Machining of Hang off Module (HOM) Rails on Deep Blue Vessel
The rails that the HOC runs on had become extremely worn and were affecting operations. The pair of rails, 11,080 mm long x 230mm wide, needed to be machined flat and to a common plane within 0.25mm.
Find Out More >