Reekie Experience
2853 04/10/2007 Bow plane Tilt Mechanism (Stbd)
2848 03/10/2007 2D PA FAN SHAFT THRUST COLLAR MACHINING
2842 01/10/2007 Alyona, taper boring rudder in yard in Vlessigen, 555 large dia, 452 small dia thro 828 length at 1 in 8 on dia taper
2843 01/10/2007 hire of 50 litre/minute 415V power pack
2838 28/09/2007 THERMAL SLEEVE FOR T-CLASS BOAT SSN13-17
2834 25/09/2007 ADDITIONAL MAIN PROPULSION WORK
O/No. K/41-07-0415
2834 25/09/2007 ACTUATOR PIN
2834 25/09/2007 ACTUATOR MOUNTING
2834 25/09/2007 NOZZLE YOKE
2834 25/09/2007 STEERING LINKAGE
2834 25/09/2007 UPPER SHAFT
2834 25/09/2007 LOWER SHAFT 124 MM DIA X 118 MM O/ALL
2834 25/09/2007 GEARBOX HOUSING
2834 25/09/2007 MOTOR TO GEARBOX COUPLING
2829 21/09/2007 Hire of Mag Base Drill and supply of cutters
2831 21/09/2007 10″ O/DIA X 22.2 MM WALL X 600 MM LONG COUNTERBORED 173 MM LONG EACH END
2831 21/09/2007 10″ O/DIA X 22.2 MM WALL X 500 MM LONG BORED THRO
2831 21/09/2007 10″ X 22.2 MM WALL X 4900 MM LONG PIPE COUNTERBORED 173 MM LONG EACH END
2831 21/09/2007 10″ O/DIA X 22.2 MM WALL X 3200 MM LONG PIPE COUNTERBORED 173 MM LONG ONE END
2831 21/09/2007 6″ O/DIA X 15.9 MM WALL X 600 MMM LONG COUNTERBORED 173 MM LONG EACH END
2831 21/09/2007 6″ O/DIA X 15.9 MM WALL X 500 MM LONG BORED THRO
2831 21/09/2007 6″ O/DIA X 15.9 MM WALL X 3600 MM LONG COUNTEREDBORED 173 MM LONG EACH END
2831 21/09/2007 6″ O/DIA X 15.9 MM WALL X 3850 MM LONG COUNTERBORED 173 MM LONG ONE END
2827 18/09/2007 Longannet unit 2 valve id S95, crop and drill out nine of twelve 1.3/4″ BSF studs on 17.1/2″ pcd and retap holes 1.3/4″ BSF
2827 18/09/2007 ISM AT LONGANNET PS WITH A FF618
2827 18/09/2007 Longannet, ism 5″ nb vlave, bore out minimum from 6.5/8″ dia to clean up cylindrical
2823 13/09/2007 10″ N.B. PIPE
2823 13/09/2007 6″ N.B. PIPE
2821 11/09/2007 Longannet, CNRV158, ism 7.3/4″ id x 11.1/4″ dia x 1/16″ high raised face and 11.1/4″ id x 14.1/4″ od bolt hole face
2818 10/09/2007 BRUSH PLOUGH CARRIERS c/w MK1,2,3,12
Case Studies
View All >
Tartan Platform – Releasing Caisson from Dead Weight Support
The customer required a robust solution to release one of their caissons from a unique dead weight support structure. The caisson had a cone feature that nested into a mating cone in the platform support.
Find Out More >
Machining of Hang off Module (HOM) Rails on Deep Blue Vessel
The rails that the HOC runs on had become extremely worn and were affecting operations. The pair of rails, 11,080 mm long x 230mm wide, needed to be machined flat and to a common plane within 0.25mm.
Find Out More >