Reekie Experience
2683 18/06/2007 HEXAGON HEAD SCREW M16x60 (ISO 4017)
2683 18/06/2007 DR1 DRILLING MACHINE INC STAND AND POWER FEED
2683 18/06/2007 36WH LOCKING SCREW (SHORT)
2678 14/06/2007 Eggborough Power Station, feed heater tap two holes 2.1/2″ BSF x 6″ dp (of a set of … on ….pcd, only 5.3/4″ clearance from hole to obstruction
2672 13/06/2007 Transportation costs associated with delivery of final goods or equipment to Customer
2672 13/06/2007 HYJECTOR BODY ‘Y’ PIECE
2677 13/06/2007 B137/008/01 MACHINE TO REMOVE 55MM FROM 18″ ID X 1″ WT SPOOL PIECE, MATCH BORE FOR 2″ THEN RECREATE PREP
2668 12/06/2007 6504 SERIES DIAPHRAGM PLATE
2668 12/06/2007 SWINGBOLT LID
2670 12/06/2007 Supply of radial and axis slideway
2670 12/06/2007 DHL Midday Express – EU
2671 12/06/2007 C.S. BRUSH PLOUGHS c/w FLATS and SCREWS
2671 12/06/2007 UPPER SEAL RING.
2667 11/06/2007 Cuan Sound Ferry “Belnahua”, ism to remove port and starboard stern tubes and leave hull bores suitable for installation of new finish machined stern tubes
2663 07/06/2007 Ø3.0M DOME END WELDED TO 100MM LONG PUP PIECE. ISM TO REMOVE PUP PIECE AND WELD PREP. 25MM WT
2664 07/06/2007 Ø3.0M DOME END WELDED TO 100MM LONG PUP PIECE. ISM TO REMOVE PUP PIECE AND WELD PREP. 25MM WT
2660 06/06/2007 DAVIT MASTS 65250 SERIES
2660 06/06/2007 DAVIT CAPSTAN NUT
2657 05/06/2007 LONGANNET PS, UNIT 1, Ø2.0″ BSF STUD DRILLING X 3-OFF
2656 04/06/2007 1000 ONE PIECE UPPER FRAME MEDIUM COARSE TO ROUGH 1459.75 DIA FINSH : TURN 1182 MM DIA : CHECK TAPER AND WELD IF CUSTOMER REQUIRES
2652 01/06/2007 additional costs
2652 01/06/2007 Affleck topside modification, ism one set of three 1,140×400 pads to clean up top faces flat, coplanar within 3mm
2650 31/05/2007 BOMAG 972RB Steering LInkage Boss Boring
2643 30/05/2007 GUIDE RAIL
2643 30/05/2007 LINTEL MEMBER
2643 30/05/2007 SILL MEMBER
2644 30/05/2007 ISM to either open out or scallop two of a set of 24 holes 60 dia thro 170 thk steel on 925.5 mm pcd to 64mm dia or by 2mm to one side to permit 2.1/4″ bolt to enter mating hole
2645 30/05/2007 Ø6.0″ NB 300# STAINLESS CLAD FLANGE ON 200MM LONG STUB OF A 4.2MM DIA VESSEL
2646 30/05/2007 DIVING BELL – BORING OF THE MAIN CABLE RELEASE PENETRATION FROM Ø42mm DIA TO APPROX Ø46.0mm DIA THRO 50mm THK
2648 30/05/2007 HIRE OF OPERATOR FOR A TALISMAN PLATFORM
Case Studies
View All >
Tartan Platform – Releasing Caisson from Dead Weight Support
The customer required a robust solution to release one of their caissons from a unique dead weight support structure. The caisson had a cone feature that nested into a mating cone in the platform support.
Find Out More >
Machining of Hang off Module (HOM) Rails on Deep Blue Vessel
The rails that the HOC runs on had become extremely worn and were affecting operations. The pair of rails, 11,080 mm long x 230mm wide, needed to be machined flat and to a common plane within 0.25mm.
Find Out More >