Reekie Experience
2583 27/04/2007 TOP GUIDE RAIL (ITEM 018)
2583 27/04/2007 MIDDLE GUIDE RAIL (ITEM 017)
2583 27/04/2007 BOTTOM GUIDE RAIL (ITEM 016)
2584 27/04/2007 16″ od x 25.4 wt pipe, cut, bore six 3080 lengths to 23.8 wt
2581 26/04/2007 ALUMINIUM TUBES
76.2 OD X 1.62 WALL X 952mm Lg
2581 26/04/2007 ALUMINIUM DOMES
2582 26/04/2007 RLNI Mersey class lifeboat, ism 3mm from 130mm wide x 7,670 mm long keel to clean up flat (whilst machine sitting parallel to and approx 600 mm above concrete floor)
2578 25/04/2007 BOC COMPRESSOR AT GRANGEMOUTH – ISM OF SLOTS IN HALF CASING TO ACCEPT WIRES
2579 25/04/2007 DOOR FRAME 2900 MM LONG X 1950 MM WIDE X 60 MM THICK COMPLETE WITH 520 MM LONG SKIRT
2579 25/04/2007 COVER PLATE 2900 MM LONG X 1950 MM WIDE X 60 MM THICK
2575 24/04/2007 STEEL BUSH 130 MM O/DIA X 120 MM I/DIA X 105 MM LONG
2575 24/04/2007 30 tonne excavator, ISM and weld build up of hinge pin hole thro stick for bucket
2576 24/04/2007 LONGANNET PS, UNIT 1, Ø2.0″ BSF STUD DRILLING X 3-OFF
2576 24/04/2007 LONGANNET PS, UNIT 1, SNRV-28 SEAT REPROFILING
2576 24/04/2007 Longannet Unit 1 3″ nb soot blower v/v’s, drill out two of two seized 1.1/2″ BSF columns and two 3/4″ BSF seized bolts
2576 24/04/2007 Longanner Unit 1 v/v FNRV drill out one of eight 5/8″ BSF studs on 5.1/4″ pcd
2576 24/04/2007 Longannet unit 1 v/v FNRV drill out three of four 3/4″ BSF studs from rectangular face for actuator arm
2576 24/04/2007 Longannet unit 1 v/v F113 machine 217 id x 245 od recess face and 245 id x 420 od bolt hole face
2576 24/04/2007 Longannet unit 1 v/v F112 drill out 1 of 12 2″ BSF studs on 17″ PCD
2568 23/04/2007 CAT 215 MAIN SLEW RING GEAR HOUSING REBORING TO Ø7.520″
2569 23/04/2007 ism 30″nbx5/8″ wt pipe at Livingston, two cuts per v/v, two v/v’s
2570 23/04/2007 ISM 28″ nb 1.063″ wt, cold cut to remove approx 2.1/2″ length from two ends of pup pieces on v/v to remove bored lenght and then form 30 + 5 – 0 degree weld prep with 0.06″ +/- 0.03″ wide root face
2567 20/04/2007 FLANGE RINGS 1646 MM O/DIA X1449 MM I/DIA X23 MM THK
2567 20/04/2007 FLANGE RINGS 1088 MM O/DIA X891 MM I/DIA X 23 MM THK
MAT SPEC:P 355 N L I
2567 20/04/2007 CAP PLATES 1646 MM O/DIA X 23 MM THK
MAT SPEC :P355 NLI
2567 20/04/2007 CAP PLATES 1088 MM O/DIA X 23 MM THK
MAT SPEC: P355 N L I
2567 20/04/2007 BLIND FLANGES 24″ O/DIA X 48 MM THK
MAT SPEC: A350 GR LF2
2563 19/04/2007 Hire of Reekie R3000, 3rd to 11th Sept
2563 19/04/2007 Hire of R3000 from 170807 to 240807 (1 day @ £675 per day in use and 5 working days @ £225 per day idle)
2563 19/04/2007 Hire of R3000 from 230707 to 310707 (1 days @ £675 per day in use and 6 working days @ £225 per day idle)
Case Studies
View All >
Tartan Platform – Releasing Caisson from Dead Weight Support
The customer required a robust solution to release one of their caissons from a unique dead weight support structure. The caisson had a cone feature that nested into a mating cone in the platform support.
Find Out More >
Machining of Hang off Module (HOM) Rails on Deep Blue Vessel
The rails that the HOC runs on had become extremely worn and were affecting operations. The pair of rails, 11,080 mm long x 230mm wide, needed to be machined flat and to a common plane within 0.25mm.
Find Out More >