Reekie Experience
2371 04/01/2007 1000 MAIN FRAME (MEDIUM COARSE)
2371 04/01/2007 1000 ONE PIECE UPPER FRAME MEDIUM COARSE TO ROUGH 1459.75 DIA FINSH : TURN 1182 MM DIA : CHECK TAPER AND WELD IF CUSTOMER REQUIRES
2369 03/01/2007 Transportation costs associated with delivery of final goods or equipment to Customer
2369 03/01/2007 TUBE 2172 OD X 20 WALL X 457 Lg
2369 03/01/2007 SLIP-ON FLANGES
2370 03/01/2007 ANGLED SHEAR MACHINING AT ROLLS-ROYCE
2366 21/12/2006 HYJECTOR VENTURI
2367 21/12/2006 FLAME HOLDER HOOD MACHINED FROM FREE ISSUE CASING
2364 19/12/2006 CHROME BAR 125 DIA X 1225 Lg
(Mill flats & drill hole only)
2361 18/12/2006 TOP HAT WITH NEW PIN ONLY
2361 18/12/2006 P.B1. 1.1/2″ DIA X 3/4″ X 3 MM THICK WASHER.
2361 18/12/2006 Phos Bronze Bush
2355 14/12/2006 C.S. BRUSH PLOUGHS c/w FLATS and SCREWS
2356 14/12/2006 C.S. BRUSH PLOUGHS c/w FLATS and SCREWS
2350 11/12/2006 CAP NUTS
2350 11/12/2006 HANDHOLE FITTING
2351 11/12/2006 TOP HALF END CASTING
2349 08/12/2006 Clydesdale Works, Bronx tube straightening machine, inlet toller lower housing, insitu bore out 1158 dia x 280 long to clean up coaxial with 240 dia 185 below
2343 07/12/2006 ‘JEAN CHARCOT’ ENGINE CYLINDER LANDING FACE
2346 07/12/2006 GROOVING TOOL TO SUIT GS HYDRO RETAINING RING GROOVE (4.0mm RADIUS NOSE )
2346 07/12/2006 HIRE OF NB4 & NB6 COMPLETE WITH STD TOOLHOLDERS AND TOOLING
2341 06/12/2006 hire of C4 to machine ten ends of 642 od x 31 wt pipe, 500 length of straight then 3,211 radius, match bore at 1:4 to 631 od x 25.4 wt, weld prep at 30 degrees
2342 06/12/2006 BODY SHELL RING 945 MM O/DIA X865 MM I/DIA X 195 MM O/ALL
2342 06/12/2006 TOP CLOSURE RING 945 MM O/DIA X 865 MM I/DIA X145 MM O/ALL
2339 05/12/2006 BEARING TOP PLATE ITEM 3C 400 MM X 380 MM X 50 MM THICK
2339 05/12/2006 GUIDE STRIP ITEM 3E 150 MM LONG X 51 MM WIDE X 45 MM THICK
2339 05/12/2006 BEARING BOTTOM PLATE ITEM 3F 394 MM X 380 MM X 50 MM THICK
2339 05/12/2006 BEARING ROCKER ITEM 3G 394 MM LONG X 150 MM WIDE X 120 MM HIGH
2334 30/11/2006 ALUMINIUM AIR SEAL RING
2315 27/11/2006 GSK Solvent recovery column sections, four off, main flanges at each end of section, ISM eight 1600id x 1760 od flanges, only 1600 id x 1650 od stst rings welded to flange faces to clean up flat to standard BS gramophone finish
Case Studies
View All >
Tartan Platform – Releasing Caisson from Dead Weight Support
The customer required a robust solution to release one of their caissons from a unique dead weight support structure. The caisson had a cone feature that nested into a mating cone in the platform support.
Find Out More >
Machining of Hang off Module (HOM) Rails on Deep Blue Vessel
The rails that the HOC runs on had become extremely worn and were affecting operations. The pair of rails, 11,080 mm long x 230mm wide, needed to be machined flat and to a common plane within 0.25mm.
Find Out More >