Reekie Experience
1679 08/11/2005 VOLPAK ?? KEY-CUTTING OF SHAFT ON PACKING MACHINE
1674 07/11/2005 COLLET
1676 07/11/2005 4″ UN -12 LH NUT TO SUIT ICE MAKER SHAFT
1676 07/11/2005 ICE MAKER SHAFT THREAD REPAIR
1671 03/11/2005 ism weld prep end of a 12″ valve, UWC-SCS-JGA-52940 rev 2
1672 03/11/2005 SPRAY ASSEMBLY
1672 03/11/2005 MACHINING OF ROTOR
1670 02/11/2005 Drill & Tap Ø2.1/2″ BSP holes drilled in press baseplate
1664 31/10/2005 WEAR PLATE BOLT c/w NUTS
1665 31/10/2005 20″ nb Flange Facing
1662 28/10/2005 C.S. BRUSH PLOUGHS c/w FLATS and SCREWS
1658 25/10/2005 BP 10″ STAINLESS STEEL FLARING
1659 25/10/2005 M27 WASHER – GRADE A4 STAINLESS STEEL
1659 25/10/2005 4MM THK CURVED LEAFSPRING SHIM
1659 25/10/2005 1MM THK CURVED LEAFSPRING SHIM
1659 25/10/2005 HANDLE USED FOR INSERTING SHIMS INTO LEAFSPRINGS
1659 25/10/2005 M27 STD NUT – GRADE A4 STAINLESS STEEL
1659 25/10/2005 MAST CAP LEAFSPRING DRILLING, Portsdown Hill
1659 25/10/2005 M27 X 80 HEX HEADED SET SCREW – GRADE A4 STAINLESS STEEL
1648 21/10/2005 CHOPPING SADDLE GIB PLATE
1648 21/10/2005 SCRAP CHOPPING SADDLE REPAIRS.
1652 21/10/2005 Drill & Tap Ø2.1/2″ BSP holes drilled in press baseplate
1646 20/10/2005 ISM Feed water v/v seat, 3″nb Hopkinsons sketch 37620, platnum seating approx 4″ bore, 8″ down from top face, angle seating
1642 19/10/2005 BP SCHIEHALLION 2-OFF 8″ DUPLEX RING GROOVES AND 1-OFF 6″ CUNIFER FLARE
1643 19/10/2005 INNER BARREL
1640 18/10/2005 UPPER OUTER AIR SEAL RING
1640 18/10/2005 LOWER OUTER AIR SEAL RING ITEM 1
1639 17/10/2005 ANY MODIFICATIONS AND PACKING TO BE CARRIED OUT FOR SO1639 (R40 SALE)
1639 17/10/2005 R40 PORTABLE FLANGE FACING MACHINE TOOL ID LOCATION, HYDRAULIC
Ø480 – Ø1016, REQUIRES 317 LONG BORE
1633 13/10/2005 VOITH COUPLING HUB WELD REPAIR AND MACHINE
Case Studies
View All >
Tartan Platform – Releasing Caisson from Dead Weight Support
The customer required a robust solution to release one of their caissons from a unique dead weight support structure. The caisson had a cone feature that nested into a mating cone in the platform support.
Find Out More >
Machining of Hang off Module (HOM) Rails on Deep Blue Vessel
The rails that the HOC runs on had become extremely worn and were affecting operations. The pair of rails, 11,080 mm long x 230mm wide, needed to be machined flat and to a common plane within 0.25mm.
Find Out More >