Reekie Experience
7024 23/03/2015 COUPLING GUARD FOR PUMP TO GEARBOX
7017 18/03/2015 Removal of Broken Bolt from Bolster. Job Sitting on Table in Workshop
7013 16/03/2015 MFR Samson Mast Cap Bearing Interface Ring, open out 32 off radial holes to Ø39
7012 13/03/2015 HINGED V.J. COUPLING ASSEMBLIES COMPLETE WITH 711 MM O/DIA COUPLING RISLAN CTD L GASKET
7010 12/03/2015 BACK WASHER (MK36)
7010 12/03/2015 SAFETY SHUT-OFF VALVE BODY
7010 12/03/2015 SAFETY SHUT-OFF VALVE SEAT
7011 12/03/2015 ASSEMBLY OF 3B Y-JET ATOMISERS
7004 11/03/2015 Seven Osprey – Equipment Lock Face
7005 11/03/2015 Agitator Shaft Sealing Area
7003 10/03/2015 MS BLANKING FLANGE
7001 09/03/2015 C.S. BRUSH PLOUGHS c/w FLATS and SCREWS
6991 02/03/2015 investigation on practicality/ feasability of milling weld prep in 541.34 od x 34 mm wall Esshete 1250 boiler spine in 90 degree arcs, operating within 98mm annular gap remotely, without requirement to remove either milling machine or welding equipment
6988 26/02/2015 COMPRESSOR PACK BASEFRAME 4300 MM LONG
6988 26/02/2015 COMPRESSOR PACK BASEFRAME 4300 MM LONG
6985 25/02/2015 Testing Machine – M24 holes
6986 25/02/2015 BI460 GDF SUEZ E&P CYGNUS UQ TOPSIDE, Machine 2990OD X 2680ID Flange
6978 19/02/2015 FABRICATED HEAT VENT
6978 19/02/2015 FABRICATED HEAT VENT
6972 18/02/2015 49 MM ECCENTRIC 1000 AUTOMAX
TO MEASURE ALL BEARING SIZES TURN IF REQUIRED AND FIT SLEEVE
6967 16/02/2015 Drill and tap 8 off M20 holes on 190PCD uphand restricted access
6964 12/02/2015 Crane Jib Boring
6963 11/02/2015 OUTER BARREL ASSEMBLY
6963 11/02/2015 INNER BARREL
6956 09/02/2015 Stringer Router Bottom Skin Rib22
6957 09/02/2015 Milling of a Shear Guideway
6960 09/02/2015 Machining required on BP Claire Ridge Flare Boom, BF/BI466/EM/MISC/060, turn 5mm aside from existing shaft to finish Ø388 +/-0.25mm x400mm length
6961 09/02/2015 Machining required on BP Claire Ridge Flare Boom, BF/BI466/EM/MISC/060, Machine up to 5mm from 2 off vertical 1.1m Dia Pads
6953 05/02/2015 Longannet, to repair damaged recessed sealing face on a flange 292mm OD x 127 ID c/w 140mm Dia x 3mm Deep Recess.
6954 05/02/2015 ST ST DOOR LUGS
Case Studies
View All >
Tartan Platform – Releasing Caisson from Dead Weight Support
The customer required a robust solution to release one of their caissons from a unique dead weight support structure. The caisson had a cone feature that nested into a mating cone in the platform support.
Find Out More >
Machining of Hang off Module (HOM) Rails on Deep Blue Vessel
The rails that the HOC runs on had become extremely worn and were affecting operations. The pair of rails, 11,080 mm long x 230mm wide, needed to be machined flat and to a common plane within 0.25mm.
Find Out More >