Reekie Experience
6088 06/08/2013 U3 Secondary Superheater Oulet Header Pressure Gauge Nozzle Trepanning. M/cing to remove three nozzles from the Ø455mm od x 96.25mm wt header. Finished holes to be 50mm, 70mm & 100m+/-0.5mm and coupon to be kept for analysis. 1-off nozzle each size
6089 06/08/2013 GENERAL PICKUP AND DELIVERY OF GOODS
6089 06/08/2013 TUP TRANSFER TRUNK SPACER RING
6094 06/08/2013 Repair to DR140 motor for R28
614010 New Blades x4
614011 Springs x2
614012 Pins x2
Skim Back plate
Skim Front Plate, remove and replace location dowel
614009 Gasket
920301 Rotor Bearings x2
Rebuild & Test
6094 06/08/2013 Hire of R28
6086 05/08/2013 LR GEAR RIB BORING
Airbus A330 Gear Rib Boring and Facing Machine
6083 01/08/2013 THERMOMETER POCKET
6083 01/08/2013 ITEM 1B UPPER STUB
6083 01/08/2013 ITEM 1A LOWER STUB
6084 01/08/2013 Hire of 1149 and Hydraulic Power Pack
6082 31/07/2013 Longannet Unit 3, Main Boiler Feed Pump, bore out the minimum from 34″ dia x 3″ length at discharge end of casing to finish 3+0.0045-0 inch diameter
6064 24/07/2013 machining work done on 4 flange faces.
6067 24/07/2013 Storage Winch Drum, Bore out Ø240 bore to Ø264, round and concentirc to 234 bore to within 0.05mm. Provide sleeve to suit
6067 24/07/2013 MS SLEEVE 264 MM O/DIA X 240 MM I/DIA X 150 MM LONG
6061 22/07/2013 Hire of milling equipment
6060 19/07/2013 POD ASSEMBLY
6060 19/07/2013 CHAMBER TOP PLATE
6060 19/07/2013 CHAMER BOTTOM PLATE
6058 18/07/2013 Hire of Type B valve lapping machine and FF20 Machine
6059 18/07/2013 9000 Ton Press, Survey both guide column and platen keyways, machine 2 off horizontal platen keyways, machine 2 off new keys off site, open out 3 off 3″ 8 UN holes out to 4.25″ 8 UN
6059 18/07/2013 MANUFACTURE NEW KEY AS PER INSTRUCTIONS
6053 17/07/2013 Sacrificial Ring
6053 17/07/2013 Seven Osprey dive support vessel Equipment lock 3.6 door trunk sealing face and sealing face on door
6053 17/07/2013 shop mc door
6051 16/07/2013 LOWER SUPPORT PLATE
6051 16/07/2013 CORNER BLOCKS (Item 2)
6052 16/07/2013 1300 UPPER FRAME TO MACHINE TAPER THEN WELD TAPER ONLY DRAWING 603 1504
6047 11/07/2013 Bore out 4 off holes from 60 to 73mm +/- 0.25mm
6041 05/07/2013 LINK TILT BASE
6041 05/07/2013 LEVER WELDMENT
Case Studies
View All >
Tartan Platform – Releasing Caisson from Dead Weight Support
The customer required a robust solution to release one of their caissons from a unique dead weight support structure. The caisson had a cone feature that nested into a mating cone in the platform support.
Find Out More >
Machining of Hang off Module (HOM) Rails on Deep Blue Vessel
The rails that the HOC runs on had become extremely worn and were affecting operations. The pair of rails, 11,080 mm long x 230mm wide, needed to be machined flat and to a common plane within 0.25mm.
Find Out More >