Reekie Experience
6004 17/06/2013 open out the 225 bore by 12mm by 80mm deep at both ends
6002 14/06/2013 SPACER RING FOR TWIST GRAB SPACER SEAT
6002 14/06/2013 Survey and machining of Grab Twist Bearing Seat, Ø1700 x 70 wide flange
5995 11/06/2013 CAT 988 Fork Assy, line bore 1 set of 4 off Ø120 bores and 1 set of 4 off Ø168 bores
5990 10/06/2013 3-1/2″O/DIA X 7/32 ” WALL TUBE X 3000 MM LONG SCREWED MALE 3 ” N.P.T.BOTH ENDS
5990 10/06/2013 2.3/8″ OD X 5/32″WALL TUBE X 200mm Lg SCREWED MALE BOTH ENDS 2″NPT
5990 10/06/2013 BEND SCREWED 5″ NPT ONE END ONLY
5991 10/06/2013 2B ‘Y’ JET ATOMISER ASSEMBLY
5987 06/06/2013 Claymore (Talsiman asset), Hydroclone vessel, Bore out N3 from
5986 05/06/2013 Camron lower tree frame stacking pot flanges, two frames, four flanges per frame
5975 03/06/2013 Babcock Appledore , OPV Vessel, insitu machining of 2 off 300×400 seats
5976 03/06/2013 Hinge boring, 1 set of three lugs, each 25mm thk, Ø60 thru 115mm total
5969 29/05/2013 Vessel Drg No PB015849 rev E, flangeDrg No PB015968 rev A
onsite machining of two main flanges, 2200 id x 2335 od sealing faces, pre glassing bore of vessel
5962 28/05/2013 2 ” N/B CARB STEEL TUBES X 6 METRES LONG SCREWED 2 ” NPT EACH END
5965 28/05/2013 MS PULLING PLATE240 MM O/DIA X 25 MM THK
5965 28/05/2013 OUTER BEARING HOUSINGS APPROX 440 MM O/DIA X 150 MM DEEP TO CHECK BORE DIMENSIONS
5965 28/05/2013 TO MACHINE OUT 420 MM BORE WELD THEN REMACHINE TO 420 MM 420.06 MM
5965 28/05/2013 JAW STOCK SHAFT APPROX 420 MM O/DIA X 1785 MM LONG TO BUILD UP WEAR WITH WELD AND REMACHINE
5966 28/05/2013 Inchgreen Dry Dock, removal of Ø100 pin
5956 24/05/2013 MS TUBES 2-1/2 ” N.B. SCHED 40 X 5200 MM LONG
5956 24/05/2013 MS TUBES 2-1/2 “N.B.SCHED 40 X 5200 MM LONG
5954 23/05/2013 COUPLING GUARD
5946 20/05/2013 STEPPED STUD 3/4″ UNC TO 5/8″ UNC
5947 20/05/2013 3B FABRICATED ATOMISER BODY
5945 17/05/2013 Your Job No 2329, Cameron lower tree frame
5936 16/05/2013 Cameron 22″ valves, inconel 625 defects in bore of stub ends
5937 16/05/2013 Seven Navica, Leith Docks, alignment check on the Seven Navica Ramp for the equipment on the Firing line
5932 15/05/2013 AMEC Enquest Knightsbridge Development Project
Hazardous Open Drain Vessel TAG 531-V-001
5921 09/05/2013 Hire of Machinist to work for TSG group
5911 07/05/2013 Canbar, Machine bearing surface on canbar
Case Studies
View All >
Tartan Platform – Releasing Caisson from Dead Weight Support
The customer required a robust solution to release one of their caissons from a unique dead weight support structure. The caisson had a cone feature that nested into a mating cone in the platform support.
Find Out More >
Machining of Hang off Module (HOM) Rails on Deep Blue Vessel
The rails that the HOC runs on had become extremely worn and were affecting operations. The pair of rails, 11,080 mm long x 230mm wide, needed to be machined flat and to a common plane within 0.25mm.
Find Out More >