Reekie Experience
5751 12/02/2013 30″ ANCHOR FLANGE
5751 12/02/2013 24″ ANCHOR FLANGE
5741 07/02/2013 LOW STAGE COMPRESSOR PACKAGE UNIT BASEFRAME
5741 07/02/2013 HIGH STAGE COMPRESSOR PACKAGE UNIT BASEFRAME
5742 07/02/2013 ST ST END CAPS 275 MM O/DIA X 310 MM O/ALL
5742 07/02/2013 ST ST END CAPS.215 MM O/DIA X 309 MM O/ALL
5744 07/02/2013 ITEM 2 STEP STUDS
5738 05/02/2013 GRADE 8.8 SELF COLOURED SET SCREWS M12 X 35 MM LONG (700-0207-70
5735 04/02/2013 Machining of Vessel Nozzle flanges
5733 01/02/2013 BRUSH PLOUGH CARRIERS c/w MK1,2,3,12
5733 01/02/2013 MACHINING OF UPPER AIR SEAL RING
5729 31/01/2013 ENGINE END BELL 3′-1 “X 9-1/8” O/ALL
MATSPEC BS 1452 G17 CAST IRON
5717 24/01/2013 UNIT3 IP ALTERNATOR FITTED BOLT/DOWEL REMOVAL APPROX 2.1/4″
5718 24/01/2013 PLATE 420 MM LONG X 220 MM WIDE X 40 MM THICK TO MACHINE PADS TO 4 MM,DRILL & BORE 1 OFF 59 MM HOLE THRO
5718 24/01/2013 PLATE 1270 MM LONG X 195 MM WIDE X 40 MM THICK TO MACHINE PADS TO 4 MM,DRILL & BORE 1 OFF 59 MM HOLE THRO
5719 24/01/2013 Extra work, a) milling seven pairs of outer reliefs,
b) grinding four inner edges to clear plummer block, c) opening out 28 NCR’ed M30 holes for helicoils, d)opening out 9 M30 holes to M36, supply and fit M30 id inserts, e) machining two side faces for
5719 24/01/2013 RH120C Track Roller Frame. Machining 7 off roller pads coplanar
5713 23/01/2013 MECO MECHANICAL SEAL TO MACHINE SAME AS SAMPLE
5709 21/01/2013 PLATE 420 MM LONG X 220 MM WIDE X 40 MM THICK TO MACHINE PADS TO 4 MM,DRILL & BORE 1 OFF 59 MM HOLE THRO
5709 21/01/2013 PLATE 1270 MM LONG X 195 MM WIDE X 40 MM THICK TO MACHINE PADS TO 4 MM,DRILL & BORE 1 OFF 59 MM HOLE THRO
5710 21/01/2013 Calmac’s Loch Portain ferry, aftr ramp, cylinder ram lugs on main and rod end eye lugs on outer
5711 21/01/2013 Building 6, vessel 19077, condenser 11-935 or 05-071 removal of a minimum of three up to a maximum of sixteen seized M16 studs on 209.4 or 325 pcd retaining 8″ nb bellows top and bottom of vessel
5705 18/01/2013 Onsite machining of top 100mm length of bore of two 6″nb and one 10″nb stub pipes each attached to hubs
5698 15/01/2013 MOUNTING PINS
5694 11/01/2013 Unit 4 HP RH TV drain flange stud holes
5691 10/01/2013 MENSA Large Sliding Door Frame Assembly, Finish machined except for 10 e x15 x 2200 long recess/rebate
2900 x 2800 outside x 2400 500 x 2400 inside, 200 wide sealing face horizontal upperrmost, in workshop at Rosyth
5681 07/01/2013 RO RO Cargo Vessel MV Beachy Head, at Teesside or Tyneside yard
insitu machining as required
5682 07/01/2013 R5000 machining of raised sealing face on vessel flange and mating dome end flange. Flange 3570 ID x 3775mm OD x 265 thk, raised sealing face 3570ID x 3674OD (52 wide).
5679 04/01/2013 IMPELLER
5675 03/01/2013 CHILL STORE UNIT BASEFRAME
Case Studies
View All >
Tartan Platform – Releasing Caisson from Dead Weight Support
The customer required a robust solution to release one of their caissons from a unique dead weight support structure. The caisson had a cone feature that nested into a mating cone in the platform support.
Find Out More >
Machining of Hang off Module (HOM) Rails on Deep Blue Vessel
The rails that the HOC runs on had become extremely worn and were affecting operations. The pair of rails, 11,080 mm long x 230mm wide, needed to be machined flat and to a common plane within 0.25mm.
Find Out More >